Full Length Die Set

• Industry standard 7/8-14" thread.
• 2 die set includes Full Length Sizer and a Crimping Seater.
• Does NOT include shell holder.

Full Length Sizer

• Industry standard 7/8-14" thread.
• Includes a decapping assembly for large primers and an expander ball for use with a 0.375" bullet.

Neck Sizer

• Industry standard 7/8-14" thread.
• Includes a decapping assembly for large primers and an expander ball for use with a 0.375" bullet.

Crimping Seater

• Industry standard 7/8-14" thread.
• Designed for use with a 0.375" bullet.
• This Crimping Seater includes a seating stem with our exclusive Venturi profile which evenly spreads the seating forces over a concentrically tapered area that greatly reduces or eliminates ring marks in your bullets.

Taper Crimp

Taper crimp dies squeeze the sides of the case wall tightly against the bullet, which effectively prevents the bullet from moving while maintaining the nice square edge of the case mouth.

• Industry standard 7/8-14" thread.

File Trim

The most consistent way to trim your cases. Simply file off and deburr anything that protrudes from the die.

File Trim dies are also extensively sized and used as the final forming die in many of our form sets.

• Industry standard 7/8-14" thread.

Dillon Trim

For use with Dillon's RT1500 Electric Case Trimmer.

Form Dies

375 Raptor can be made from either 308 or 358 Winchester. In both cases, the parent case needs to be "necked up" (case mouth expanded or opened up) and then trimmed to length. 308 Winchester requires two expanding operations while 358 Winchester only needs one. Our forming set comes complete with everything you need to handle either caliber.

• Industry standard 7/8-14" thread.
• Includes 2 tapered expanders, 2 expander die bodies, and file trim die.

Reamer Die

• Industry standard 7/8-14" thread.
• Complete with reamer.

No 444 H Press

Originally released as the single station Magnum H Press. Then the triple station 333 H Press. These earlier versions were made from cast aluminum which was light and easy to work with. Unfortunately it also forced all high pressure operations like forming and sizing to be done in the center rear station.

The four station 444 H Press is the latest version. It is made from plate steel and considerably stronger in every way!

With four stations available, you will not have to constantly reset your dies for each step. Preset each station once, and you're ready to go. No turret to wear or wobble. Pressures are centered between two 7/8" solid steel shafts. The platen rides on bronze bushings.

• Uses industry standard 7/8"-14 dies and snap-in shell holders
• Complete with large and small priming arm and primer catcher.
• Loads everything from the smallest pistol cartridge to the largest magnum rifle cases with ease, including full-length resizing.
• Mounts on any flat table-top. Nothing to turn or jam. You move only the cases. There is adequate hand room and sufficient platen travel for cartridges up to 4" long.

# 1 Shell Holder

Our snap-in shell holders fit all modern presses designed to use a snap-in shell holder. Due to the wide variety of brass available, we recommend sending us sample cases when ordering shell holders for obsolete and wildcat caliber's.

• See our Caliber list for shell holder caliber reference. Note that the Caliber List does not contain the full part number. We commonly abbreviate shell holder numbers by omitting the "408".

Standard Deburring Tool

Chamfers and deburs the inside and outside of the case mouth for easy bullet seating.

• Works on all cases from 45 to 60 caliber.
• Hardened to 59 Rockwell C for extra long life.

1 1/4-12 x 7/8-14 Press Top Bushing

• Industry standard thread : .
• Designed for use with all modern presses that accept interchangeable top bushings.